[an error occurred while processing this directive]


|
High Perfomance Injection Molding machines, MAURGAN, Taiwan
 Specification: Models Performances | Unit. | ÀÌÀ-45 | ÀÌÀ-60 | ÀÌÀ-120 | ÀÌÀ-140 | ÀÌÀ-160 | Injection system | Screw diameter | mm | 25 | 28 | 25 | 28 | 32 | 32 | 36 | 40 | 36 | 40 | 45 | 40 | 45 | 50 | Screw L/D ratio | -- | 20 | 17.2 | 22.4 | 20 | 17.5 | 22.5 | 20 | 18 | 22.2 | 20 | 17.7 | 22.5 | 20 | 18 | Injection weight (ps) | gram | 45 | 57 | 54 | 68 | 90 | 134 | 170 | 210 | 189 | 233 | 295 | 256 | 324 | 400 | Calculated shot volume | cm3 | 49 | 62 | 59 | 74 | 96 | 159 | 198 | 240 | 203 | 251 | 318 | 276 | 350 | 432 | Injection nressure | kg/ ñm3 | 2333 | 1714 | 2720 | 2196 | 1660 | 2054 | 1623 | 1315 | 2338 | 1894 | 1496 | 2117 | 1673 | 1355 | Injection rate | cm3/sec | 70 | 88 | 55 | 69 | 90 | 107 | 135 | 167 | 116 | 143 | 181 | 138 | 175 | 216 | Plasticizing capacity (ps) | g/ sec | 4.8 | 7.3 | 5.2 | 7.3 | 10.4 | 16 | 22 | 31 | 22 | 31 | 43 | 29 | 39 | 56 | Injection stroke | mm | 100 | 120 | 180 | 200 | 220 | Injection time | sec | 0.7 | 1.07 | 1.35 | 1.75 | 1.75 | Clamping system | Clamping stroke | mm | 200 | 245 | 322 | 380 | 420 | Clamping force | ton | 45 | 60 | 120 | 140 | 160 | Mold thickness (min-max) | mm | 100~300 | 100~320 | 120~380 | 120~420 | 150~450 | Inner distance of tie bars (ÍXV) | mm | 264õ264 | 310õ310 | 364õ364 | 410õ410 | 458õ440 | Ejection stroke | mm | 75 | 75 | 100 | 100 | 130 | Ejection force | ton | 2.2 | 2.2 | 3.3 | 4.6 | 4.6 | Electric system | Electric motor power | Hp | 10 | 10 | 15 | 20 | 25 | Hydraulic system pressure | kg/ cm3 | 140 | 140 | 140 | 140 | 140 | Heater capacity | Kw | 4.6 | 4.6 | 5.7 | 6.4 | 8.0 | Heating zones | set | 4 | 4 | 4 | 5 | 5 | Total power | kw | 12.1 | 12.1 | 16.95 | 23 | 26.75 | other | Oil tank capacity | L | 180 | 180 | 220 | 320 | 350 | Machine measurements | M | 3.8õ1õ1.5 | 4.1õ1õ1.6 | 4.4õ1.2õ1.7 | 4.9õ1.3õ1.9 | 4.9õ1.3õ1.9 | Net weight | kg | 3100 | 3600 | 3900 | 5400 | 6500 |
Models Performances | Unit | ÀÌÀ-200 | ÀÌÀ-220 | ÀÌÀ-250 | ÀÌÀ-300 | ÀÌÀ-350 | Injection system | Screw diameter | mm | 45 | 50 | 55 | 50 | 55 | 60 | 55 | 60 | 65 | 60 | 65 | 70 | 60 | 65 | 70 | Screw L/D ratio | -- | 22.2 | 20 | 18.2 | 22 | 20 | 18.3 | 21.8 | 20 | 18.5 | 20 | 18.5 | 17.1 | 21.7 | 20 | 18.6 | Injection weight (ps) | gram | 354 | 437 | 528 | 473 | 572 | 681 | 652 | 776 | 911 | 786 | 922 | 1070 | 838 | 984 | 1141 | Calculated shot volume | cm3 | 381 | 471 | 570 | 510 | 618 | 735 | 665 | 792 | 929 | 848 | 995 | 1154 | 905 | 1062 | 1232 | Injection nressure | kg/ cm3 | 2130 | 1725 | 1426 | 2046 | 1691 | 1421 | 1978 | 1662 | 1416 | 1662 | 1416 | 1220 | 2083 | 1775 | 1530 | Injection rate | cm3/sec | 168 | 208 | 251 | 174 | 211 | 251 | 227 | 270 | 318 | 273 | 321 | 372 | 258 | 303 | 352 | Plasticizing capacity (ps) | g/ sec | 39 | 56 | 68 | 56 | 68 | 86 | 49 | 59 | 69 | 59 | 69 | 73 | 63 | 72 | 85 | Injection stroke | mm | 240 | 260 | 280 | 300 | 320 | Injection time | sec | 1.99 | 2.27 | 2.93 | 3.1 | 3.5 | Clamping system | Clamping stroke | mm | 450 | 480 | 522 | 600 | 650 | Clamping force | ton | 200 | 220 | 250 | 300 | 350 | Mold thickness (min-max)) | mm | 180~520 | 200~550 | 200~580 | 200~700 | 200~750 | Inner distance of tie bars (ÍXV) | mm | 482õ452 | 520õ485 | 561õ561 | 620õ620 | 660õ620 | Ejection stroke | mm | 722õ752 | 780õ780 | 880õ880 | 910õ940 | 960õ940 | Ejection force | mm | 130 | 130 | 130 | 150 | 150 | Ejection force | ton | 4.6 | 4.6 | 6.2 | 5.9 | 5.9 | Electric system | Electric motor power | Hp | 25 | 30 | 40 | 40 | 50 | Hydraulic system pressure | kg/ cm3 | 140 | 140 | 140 | 140 | 140 | Heater capacity | Kw | 10 | 14 | 14 | 20.2 | 25 | Heating zones | set | 6 | 6 | N+5 | N+5 | N+5 | Total power | kw | 27.5 | 36.5 | 35.8 | 50.2 | 62.5 | other | Oil tank capacity | L | 450 | 450 | 450 | 600 | 650 | Machine measurements | M | 5.7õ1.4õ2.1 | 6õ1.5õ2.3 | 6.2õ1.6õ2.4 | 6.8õ1.7 | 7õ1.8õ2.7 | Net weight | kg | 7800 | 9200 | 13100 | 14000 | 16000 |
Models Performances | Unit | ÀÌÀ-400 | ÀÌÀ-450 | ÀÌÀ-500 | ÀÌÀ-550 | ÀÌÀ-600 | Injection system | Screw diameter | mm | 65 | 70 | 75 | 70 | 75 | 80 | 75 | 80 | 85 | 80 | 85 | 90 | 85 | 90 | 95 | Screw L/D ratio | -- | 21,5 | 20 | 18.7 | 21.4 | 20 | 18.7 | 21,3 | 20 | 18.8 | 21.3 | 20 | 18.9 | 22.4 | 21.1 | 20 | Injection weight (ps) | gram | 1076 | 1248 | 1433 | 1355 | 1555 | 1770 | 1630 | 1863 | 2103 | 1677 | 1893 | 2122 | 2208 | 2476 | 2758 | Calculated shot volume | cm3 | 1161 | 1347 | 1546 | 1462 | 1678 | 1910 | 1767 | 2010 | 2270 | 1810 | 2043 | 2290 | 2383 | 2672 | 2977 | Injection nressure | kg/ cm3 | 1175 | 1530 | 1331 | 1920 | 1167 | 1470 | 1673 | 1470 | 1310 | 1838 | 1628 | 1452 | 1628 | 1452 | 1220 | Injection rate | cm3/sec | 314 | 364 | 418 | 348 | 400 | 454 | 420 | 478 | 540 | 345 | 390 | 437 | 468 | 524 | 584 | Plasticizing capacity (ps) | g/ sec | 68 | 78 | 89 | 39 | 56 | 68 | 86 | 92 | 86 | 89 | 101 | 109 | 104 | 112 | 124 | Injection stroke | mm | 350 | 380 | 400 | 360 | 420 | Ejection force | sec | 3.7 | 4.2 | 4.2 | 5.1 | 5.1 | Clamping system | Clamping stroke | mm | 680 | 700 | 780 | 750 | 900 | Clamping force | ton | 400 | 450 | 500 | 550 | 600 | Mold thickness (min-max)) | mm | 250~750 | 250~850 | 250~950 | 250~950 | 300~1100 | Inner distance of tie bars (ÍXV) | mm | 700õ700 | 758õ700 | 808õ808 | 850õ800 | 905õ900 | Ejection stroke | mm | 1070õ1040 | 1130õ1040 | 1178õ1120 | 1250õ1200 | 1300õ1260 | Ejection force | mm | 200 | 200 | 200 | 200 | 200 | Ejection force | ton | 8.9 | 8.9 | 8.9 | 8.5 | 8.9 | Electric system | Electric motor power | Hp | 50 | 60 | 60 | 60 | 50+50 | Hydraulic system pressure | kg/ cm3 | 140 | 140 | 140 | 140 | 140 | Heater capacity | Kw | 25 | 25 | 31 | 31 | 36.8 | Heating zones | set | N+6 | N+6 | N+6 | N+6 | N+6 | Total power | kw | 62.5 | 62.5 | 76.0 | 76.0 | 111.8 | other | Oil tank capacity | L | 700 | 750 | 800 | 800 | 1100 | Machine measurements | M | 7,4õ1.9õ2.8 | 7.6õ2õ2.9 | 8.1õ2.1õ.3.1 | 8.1õ2.0õ2.9 | 8.8õ2.4õ3.4 | Net weight | kg | 18000 | 21000 | 25500 | 26500 | 29500 |
Models Performances | Unit | ÀÌÀ-650 | ÀÌÀ-800 | ÀÌÀ-1000 | ÀÌÀ-1250 | ÀÌÀ-1600 | Injection system | Screw diameter | mm | 90 | 95 | 100 | 95 | 105 | 105 | 115 | 115 | 125 | 125 | 135 | Screw L/D ratio | -- | 21,1 | 20 | 19 | 20 | 19 | 20 | 18.2 | 20 | 18.4 | 20 | 18.5 | Injection weight (ps) | gram | 2298 | 2561 | 2838 | 2889 | 3630 | 4011 | 4812 | 5389 | 6367 | 7106 | 8288 | Calculated shot volume | cm3 | 2481 | 2764 | 3063 | 3119 | 3810 | 4330 | 5193 | 5819 | 6872 | 7670 | 8946 | Injection nressure | kg/ cm3 | 1879 | 1687 | 1522 | 2036 | 1837 | 1921 | 1601 | 1973 | 1670 | 1864 | 1597 | Injection rate | cm3/sec | 459 | 512 | 567 | 528 | 646 | 674 | 809 | 840 | 993 | 917 | 1069 | Plasticizing capacity (ps) | g/ sec | 106 | 118 | 140 | 126 | 169 | 169 | 212 | 212 | 262 | 262 | 304 | Injection stroke | mm | 390 | 440 | 500 | 560 | 625 | Ejection force | sec | 5.3 | 5.85 | 6.42 | 6.92 | 8.37 | Clamping system | Clamping stroke | mm | 850 | 1000 | 1200 | 1450 | 1650 | Clamping force | ton | 650 | 800 | 1000 | 1250 | 1600 | Mold thickness (min-max)) | mm | 300~1100 | 400~1200 | 500~1300 | 600~1400 | 700~1600 | Inner distance of tie bars (ÍXV) | mm | 950õ900 | 1060õ960 | 1160õ1060 | 1270õ1160 | 1500õ1400 | Ejection stroke | mm | 1380õ1467 | 1531õ1454 | 1590õ1653 | 1930õ1930 | 2450õ2450 | Ejection force | mm | 200 | 250 | 250 | 320 | 320 | Ejection force | ton | 8.5 | 15.5 | 15.8 | 22.0 | 22.0 | Electric system | Electric motor power | Hp | 50+50 | 50+50 | 60+60 | 75+75 | 75+75+60 | Hydraulic system pressure | kg/ cm3 | 140 | 140 | 140 | 140 | 140 | Heater capacity | Kw | 36.8 | 36.8 | 53.6 | 69.5 | 82.6 | Heating zones | set | N+6 | N+6 | N+6 | N+6 | N+6 | Total power | kw | 111.8 | 111.8 | 158.60 | 197.0 | 240.1 | other | Oil tank capacity | L | 1100 | 1400 | 1700 | 2300 | 2800 | Machine measurements | M | 9,5õ2.1õ3.1 | 10.2õ2.5õ3.5 | 12.4õ3.1õ.3.8 | 14.2õ3.5õ4.1 | 14.8õ3.9õ4.6 | Net weight | kg | 30100 | 45000 | 63000 | 80000 | 92000 |
*Specifications are subject to change without prior notice. 
Standard equipment: 1. Full set of o-rings 2. Full set of PCB’s 3. Working oil – 1 set. 4. Full set of spare parts Optional accessories: 1. Chiller 2. Crusher 3. Hooper Dryer 4. Hopper Louder 5. Master Batch Feeder 6 Mixer 7 Color mixer 8 Mold Temperature Controller
© 2003 «AMIGO INTERNATIONAL LTD.» Address: Russia, 119331, Moscow, Prospekt Vernadskogo, 29, 8th floor, office 804b. Phone: (499) 131-9900, 133-9042, 133-5441; Fax: (499) 138-1411; Email: amigo@amigogroup.ru
|
[an error occurred while processing this directive]





|